How to determine whether you need an 8oz or a 32oz bottle.

Our 8oz. bottle can be used for minor drip leaks. Use 1 whole bottle regardless of the amount of water in the tub, ranging from 250 to 1000 gallons. Water Temperature should be between 70F and up.

Water leaks in hot tub or spa plumbing can be troublesome and in most cases very difficult to locate due to the foam sprayed insulation. The time and effort for a manual repair can at times become quite costly.

With FIX A LEAK the repair costs can be minimal and often be done by the hot tub or spa owner.

Instructions for use:

This type of application will be for hot tub/spa leaks that are minor in nature. When you know your hot tub/spa is leaking but cannot detect a noticeable water drop inside the spa a wet spa pad or actual water slowly dripping onto the pad or floor may be the cause. Since it will be difficult to determine if you have sealed this type of leak follow the steps below.

Remove all cartridge filters.

Pour the entire contents of the bottle into the filter intake or directly into the spa.

On day 1 run the spa for 4-6 hours, alternating between the low and high-speed jets.

Since the jets usually run on a 15-minute cycle, you must be present to restart once cycle kicks off.

After the 4-6 hours you can shut off your spa or just allow the recirculating pump to periodically run its cycle.**

On day two, if the leak has slowed but not stopped, broom the bottom of your hot tub/spa before restarting the process as you did on day one of alternating between high and low speed jets for 4-6 hours.

After day two leave the spa off for 48 hours. During this time frame check to see if the water level is stable and if the hot tub/spa pad remains dry.

**Note: The leak may stop after the first day, in which case you can
proceed to the instructions below.

We recommend to drain your spa after treatment as long as night temperatures remain over 40F. If temperatures dip below 40F for any length of time you may reinstall the filter(s) and remove the remainder of Fix A Leak out of the Spa or Hot Tub, making sure to take them out now and then to rinse under hot water to remove any Fix A Leak residue. If you are able to drain the Spa make sure that as the water level is going down to wipe down the Spa with a warm wet soft cloth[s] or towel[s] to ensure all remaining residue of Fix A Leak is removed. If it is not thoroughly wiped away it can leave a white residue. Once the Spa shell is cleaned, let the Spa sit empty for 5-7 days to attempt to cure the FIX A LEAK from the inside of the plumbing pipe[s] (as the foam insulation will remain wet or damp for months on end).
Keep in mind water may still drip from the saturated foam surrounding the hot tub/spa.

With this procedure you should have a success rate of 80%.

Once this process is completed, refill your spa, add your chemicals and resume normal operation. 

 

A 32oz. bottle may be required: depending on the severity of the leak usually between 1 inch to 1 and a half inches, per 24 hour period. This would allow you to begin by using 1/3 of the bottle and if more product is required you can add the additional amount. Water temperatures should br between 70F and up.

As this is a repair do not use your hot tub/spa until the FIX A LEAK has been removed either by draining or filtering out.

Recommended procedure for using FIX A LEAK:

Determine water loss in a 24-hour period by measuring the water level drop in that period.

Fill hot tub/spa to the original level and mark the water line.

Remove filter cartridge(s) or other filtering devices. For sand filters, place the filter valve on recirculate.

Ensure to shake bottle well.

NOTE: Placing the bottle into a container of hot water for several minutes prior to shaking will ensure product is properly mixed.

With circulating pump running slowly add the FIX A LEAK through the filter cartridge intake or pour directly into the hot tub/spa.

If you are losing close to an inch and a half per day only use your low speed jets. If you are losing an inch or less alternate between you low and high-speed jets As these jets are meant to run usually for 15 minutes you will have to ensure to kick them on when they shut off.

Run for 4-6 hrs. minimum you can run for a longer period of time up to 6-8 hrs. if you wish.

Once this is done you can allow the circulating pump to run its cycle as there will be no need to run your other pumps.

Check your water level the following day. If the level remains the same, the leak has stopped.

If the leak has slowed but not totally stopped, you can add more FIX A LEAK to increase the strength of solution already in the hot tub/spa and repeat the same procedure as you did on day one.

Check again the day after. If all goes well and the leak has stopped shut off your hot tub/spa for 48 hrs.

If the level holds, we recommend to drain your hot tub/spa after treatment as long as night temperatures remain over 40F. If temperatures dip below 40F for any length of time you may reinstall your filter cartridge(s) and collect the product into the filter(s). This may involve a couple of cleanings. Immerse cartridges into a container of warmer water for several minutes and then rinse out under a tap, or rinse out with a garden hose.

If you are able to drain the hot tub/spa, make sure that as the water level is going down, to wipe down the hot tub/spa with a warm wet non abrasive cloth(s) or towel(s) to ensure all remaining FIX A LEAK is removed. If it is not thoroughly wiped away it can leave a white residue.

Once the spa / hot tub shell is cleaned properly, allow it to be empty for 5-7 days to attempt to cure the product from the inside of the plumbing pipe(s). The foam insulation will remain wet or damp for several months. Keep in mind some water may still drip from the saturated foam surrounding the spa. Once this process is completed, refill your spa / hot tub, add your chemicals and resume normal operation.

Once your filters have been thoroughly cleaned, reinstall and resume normal operation.

With these procedures you should have a success rate of 80%.

I had a leak in a 36x16 vinyl inground pool. When I came back from a week vacation the pool had 2 feet lower level. By the time I figured out what to do, I was missing 3 feet. The product arrived in one day. One day later I had no leak.

Gabriel Popescu